Building automation system, sensor
AI-Powered Image SearchSelected tag
Tag Selection
The TRTN temperature transmitters are intended for room mounting in HVAC systems. The temperature sensor gives output signal 0...10 V DC or 4...20 mA via the built-in electronics.
Supply voltage
For output signal 0...10 V, the transmitter should be supplied with 15...40 V DC or 24 V AC Ā±20%. For output signal 4...
Supply voltage
For output signal 0...10 V, the transmitter should be supplied with 15...40 V DC or 24 V AC Ā±20%. For output signal 4...
More Details...
Function
Transmitters intended for wall mounting in HVAC systems. The sensor is mounted in the cover-part of the casing. The cover is easy to detach from the back by means of snap-in grips and detachable terminals. This makes mounting easier. Furthermore, no cables have to be disconnected, simplifying service and replacement.
Transmitters intended for wall mounting in HVAC systems. The sensor is mounted in the cover-part of the casing. The cover is easy to detach from the back by means of snap-in grips and detachable terminals. This makes mounting easier. Furthermore, no cables have to be disconnected, simplifying service and replacement.
More Details...
The temperature transmitters have an element which gives a signal that is proportional to the temperature. The measuring signal is converted by the built-in electronics to output signal,0...10 V or 4...20 mA.
More Details...
For measuring room temperature. For use with the Aqualine-, Pulser-, TM- and TTC-series. The scale can be locked with the screw under the cover. TG-R430 can also be used for setpoint adjustment only.
Sensor with NTC-element for measuring outdoor temperature or in rooms where a higher protection class is needed. TG-R6... are room sensors intended for use with the Aqualine, PULSER, TM, TTC and Floorigo ranges.
• Protection class IP54
• Easy to mount
• Protection class IP54
• Easy to mount
Sensor with NTC-element for measuring room temperature. TG-R5... are room sensors intended for use with the Aqualine, PULSER, TM, TTC, Prigo and Floorigo ranges.
Average temperature sensor with four Pt1000-elements, intended for duct mounting.Ā TG-MH/PT1000 is an average temperature sensor for duct mounting. It has a 3 m cable with four Pt1000- elements. The cable is mounted with clamps and is held in place by an end spring. The sensor has a modern design that fits into any environment.
More Details...
Temperature sensors with PT100- or PT1000-element intended for duct mounting.Ā Temperature sensors in the Tempero-series with a modern design that fits into any environment. The sensors are intended for duct mounting. TG-KH/PT100, TG-KH/PT1000 and TG-KH/ PT1000-430 have adjustable insertion length and an
elastic and flexible mounting bracket that closes tightly against ducts.
elastic and flexible mounting bracket that closes tightly against ducts.
More Details...
Temperature sensors with PT100- or PT1000-element and wiring housing, intended for measuring water temperature.Ā Sensors in the Tempero-series that have a modern unobtrusive design. The sensors are intended for measuring water temperature.
More Details...
Immersion sensor for water temperature measurement.
Technical data
Technical data
- Temperature range = -30...+70Ā°C
- Time constant = 4 s
- Protection class = IP65
- Connection = R1/4ā
- Insertion length = Max. 300 mm.
- Cable length = 1.
More Details...
Temperature sensors intended for measuring surface temperature. The sensors have PT100- or PT1000- element.Ā Modern sensors in the Tempero-series that have an unobtrusive design. TG-AH/PT100 and TG-AH/PT1000 are intended for clamp-on mounting. Clamp and heat conductive contact paste are included.
More Details...
For measuring surface temperature. For use with the Aqualine-, TM- and TTC-series. Delivered with clamp. N.B. This sensor cannot be used with the Pulser-series.
For measuring air temperature in ventilation ducts. For use with the Aqualine-, Pulser-, TM- and TTC-series.
Universal sensor. For use with the Aqualine-, TM- and TTC-series. N.B. This sensor cannot be used with the Pulser-series.
For panel mounting. For use with the Aqualine-, Pulser-, TM- and TTC-series (not TBI-PT1000).
The transmitter consists of a stainless steel sensor hausing and a ceramic membrane. Resistors are applied to the membrane by means of thick-film technology.
Pressure affecting the membrane gives a change in resistance depending on the flexing of the membrane. The resistance value is transferred to a proportional
output signal by means of the built-in electronics.
Pressure affecting the membrane gives a change in resistance depending on the flexing of the membrane. The resistance value is transferred to a proportional
output signal by means of the built-in electronics.
More Details...
Function
The transmitter consists of a plastic sensor housing and a membrane of silicone LSR. The differential pressure affects the membrane which is connected to the sensor element. The element is manufactured with state-of-the-art technology and has a ceramic beam onto which thick-film resistors have been applied.
The transmitter consists of a plastic sensor housing and a membrane of silicone LSR. The differential pressure affects the membrane which is connected to the sensor element. The element is manufactured with state-of-the-art technology and has a ceramic beam onto which thick-film resistors have been applied.
More Details...
The transmitter consists of a plastic sensor-housing and a membrane of silicon LSR. The differential pressure affects the membrane which is connected to the sensor element. The element is manufactured with state-of-the art technology with a ceramic beam onto which thick-film resistors have been applied.
More Details...
The transmitter consists of a sensor hausing in stainless steel and a ceramic membrane. Resistors are applied to the membrane in thick film technology. The pressure affecting the membrane results in a change of resistance value depending on the bending of the membrane and this is transferred by means of the built-in electronics to a proportional output signal.
More Details...
Application
The differential pressure transmitter is used in building automation to monitor pressure in air and other noncorrosive gases. Three different models are available for an optimal adaptation to the application. All models are equipped with a LED display which makes it easy to read out the pressure value.
The differential pressure transmitter is used in building automation to monitor pressure in air and other noncorrosive gases. Three different models are available for an optimal adaptation to the application. All models are equipped with a LED display which makes it easy to read out the pressure value.
More Details...
The differential pressure transmitter DMD is based on microprocessor technology and it has a logical menu system. Settings of working range, damping, and zero-point adjustment are made using buttons under the lid.
Measuring technique
Pressure measurments are obtained by means of a sensor that uses a ceramic measuring beam.
Measuring technique
Pressure measurments are obtained by means of a sensor that uses a ceramic measuring beam.
More Details...
Function
Transmitters intended for wall mounting in HVAC systems. Temperature sensors The unit has a built-in temperature sensor, working range 0...50Ā°C.
Relative humidity
The transmitters have a capacitive thin-film element that provides a signal proportional to the relative humidity.
Transmitters intended for wall mounting in HVAC systems. Temperature sensors The unit has a built-in temperature sensor, working range 0...50Ā°C.
Relative humidity
The transmitters have a capacitive thin-film element that provides a signal proportional to the relative humidity.
More Details...
HTDT2500 has a capacitive thin-film element that provides a signal propotional to the relative humidity. The transmitter has a high degree of accuracy. The
measuring element responds quickly to changes in humidity. The transmitter has excellent long-term stabilty and a low hysteresis. It can withstand up to 100 % RH (condensing) without accuracy being affected.
measuring element responds quickly to changes in humidity. The transmitter has excellent long-term stabilty and a low hysteresis. It can withstand up to 100 % RH (condensing) without accuracy being affected.
More Details...
HRT250 humidity transmitter is intended for wall/ room-mounting in HVAC-applications, swimming baths, greenhouses,stables etc. The humidity transmitter has a capacitive thin-film element which gives a signal that is proportional to the relative humidity.
More Details...
